- #Cp2104 windows 10 driver serial
- #Cp2104 windows 10 driver drivers
- #Cp2104 windows 10 driver software
This carrier board connects the VIO pin of the CP2104 to VDD by default, setting its logic voltage level to the 3.45 V provided by the IC’s built-in voltage regulator. You can also solder wires directly to the pads for the smallest installation. The carrier board ships with a 1×25 straight male header strip, a 1×6 right-angle male header strip, and a 1×6 right-angle female header as shown below. As a result, this CP2104 adapter board can be used as a drop-in replacement for an FTDI cable in many applications, such as programming Arduino-compatible boards.ĬP2104 USB-to-serial adapter carrier in a breadboard with included 0.1″ male headers installed.ĬP2104 USB-to-serial adapter carrier with included 6-pin 0.1″ right-angle female header installed. This gives access to six signals (RTS, RX, TX, VBUS, CTS, and GND) that are commonly found on FTDI cables and other similar USB-to-serial adapters. This allows any pin to be accessed easily while the adapter is plugged into a solderless breadboard, as shown in the left picture below.Īlternatively, a 1×6 header can be soldered to the end of the board, as shown in the right picture below.
"Ring indicator" control input (active low)Īll of the adapter’s pins are available in two rows spaced 0.5″ apart along the sides of the board. "Data carrier detect" control input (active low) "Data terminal ready" control output (active low) (often used with DSR) "Data set ready" control input (active low) (often used with DTR) “Ready to send” control output (often used with CTS) “Clear to send” control input (often used with RTS)
#Cp2104 windows 10 driver serial
Supported baud rates: 300 bps to 2 MbpsĪsynchronous serial data transmit (idle high).Logic voltage level: 3.45 V (5 V tolerant).Dimensions: 0.6″ × 0.95″ including connector.This product requires a USB A to Micro-B cable (not included) to connect to a computer.įor a similar adapter with a USB Mini-B connector, please see the Pololu USB-to-Serial Adapter.
#Cp2104 windows 10 driver drivers
Drivers are available from Silicon Labs for Windows XP, Windows Vista, Windows 7, Windows 8, Windows 10, Linux, and Mac OS X. The CP2104 is a full-speed USB 2.0 device and allows baud rates of up to 2 Mbps.
#Cp2104 windows 10 driver software
The adapter looks like a standard virtual serial port (COM port) to the computer’s operating system, which means it can be used with any software designed to work with a serial port (even a legacy RS-232 port). The green LED on the SUSPEND line indicates an active USB connection when lit.
This board uses 3.45 V signal levels by default, but the signal pins can tolerate higher voltages, allowing the adapter to be used with 5 V systems that see 3.45 V as a logic high. It offers several options for accessing the data, control, and GPIO pins on the CP2104, all of which are made available on a 0.1″ spacing. The tiny unit measures only 0.6″ × 0.95″ including its Micro-USB connector. This USB-to-serial adapter is a breakout board for the Silicon Labs CP2104 USB-to-UART bridge, and it is a great solution for connecting microcontroller projects and other logic-level serial devices to a personal computer. OverviewĬP2104 USB-to-serial adapter carrier, bottom view with dimensions. Its lower-priced successor, the CP2102N USB-to-Serial Adapter Carrier can be used as a drop-in replacement in most applications, and it offers a few improvements including support for higher baud rates (up to 3 Mbps) and a re-programmable configuration ROM. Note: This product is not recommended for new designs (NRND) based on Silicon Labs designating the CP2104 as NRND.
0 kommentar(er)
